Almost every hot tub job starts with one number: how many gallons the tub holds. Chemical doses, heating costs, fill time, and whether your deck can carry the tub all depend on it. Measure your tub, enter the numbers below, and you’ll get the volume, the filled weight, and the load on the surface underneath.
Hot Tub Volume Calculator
Find how many gallons your hot tub holds, what it weighs full, and the load it puts on a deck or pad.
Seats, loungers and footwells take up a lot of space, so a hard-shell tub holds about half of what its measurements suggest.
Measure inside the shell, from wall to wall across the water surface, and from the water line down to the floor of the footwell.
Estimated Water Volume
gallons
About liters
Load on the Surface Below
lb per sq ft
Spread over square feet. A typical residential deck is designed for about 50 lb per sq ft, so most full hot tubs need a concrete pad or a deck built or reinforced for the load.
Now that you know your gallons, get exact doses with our Hot Tub Chemical Calculator, or see what your tub costs to run with the Hot Tub Running Cost Calculator. Planning where to put it? Price the pad and wiring with the Hot Tub Installation Cost Calculator.
How Many Gallons Does a Hot Tub Hold?
Most residential hot tubs hold between 200 and 500 gallons. Seating capacity is the best quick guide:
| Tub size | Typical gallons | Typical filled weight (with people) |
|---|---|---|
| 2–3 person | 200–300 | 2,500–3,500 lb |
| 4–5 person | 300–400 | 3,500–4,800 lb |
| 6–7 person | 400–500 | 4,800–6,000 lb |
| 8+ person / swim spa | 500–2,000+ | 6,000 lb and up |
Inflatable tubs hold more water than their seat count suggests because they have no molded seats. A 4-person inflatable usually holds 200–250 gallons, and a 6-person model holds 250–300.
Why Measurements Alone Overestimate Hot Tub Volume
Multiplying length × width × depth works for a pool, but not for a hard-shell hot tub. Seats, loungers, the footwell and the equipment cavity all take up space inside the shell. Only about half of the box made by the tub’s inside dimensions actually holds water. That’s why the calculator applies a fill factor of 0.48 for molded tubs and 0.95 for flat-floor tubs such as inflatables, wooden tubs and stock tanks.
The most accurate number is still the one on the manufacturer’s spec sheet. If you know your make and model, check it first, and use the calculator when you can’t find it.
How to Measure Your Hot Tub
- Inside length and width: measure wall to wall across the water surface, inside the shell, not across the outside cabinet.
- Diameter (round tubs): measure straight across the widest point of the water surface.
- Depth: measure from the water line down to the floor of the footwell, which is the deepest point. Most hard-shell tubs are 34–40 inches deep, and inflatables are about 25–28 inches.
- Outside footprint: measure the cabinet’s outside length and width. This is the area the weight is spread across.
Hot Tub Weight and Deck Load
Water weighs about 8.34 pounds per gallon, so a 400-gallon tub carries roughly 3,300 pounds of water. Add 500–900 pounds for an empty hard-shell tub and about 175 pounds per bather, and a full 6-person tub can top 5,000 pounds.
The load per square foot matters more for a deck than the total weight. A typical residential deck is designed for about 50 pounds per square foot (40 live plus 10 dead). A full hard-shell hot tub usually puts 90–120 pounds per square foot on its footprint, roughly double what a standard deck is built for. Most tubs therefore sit on a 4-inch reinforced concrete pad, or on a deck framed specifically for the load and checked by a builder or engineer.
How Long Does It Take to Fill a Hot Tub?
A typical garden hose delivers 5–10 gallons per minute depending on water pressure and hose diameter. A 400-gallon tub takes about 40–80 minutes to fill. Fill through the filter well so water pushes air out of the plumbing, which helps prevent airlocks in the pump. Then let the heater bring the water up to temperature, which usually takes 12–24 hours from cold.
What to Do With Your Gallon Number
- Dose chemicals correctly: plug your gallons into the Hot Tub Chemical Calculator for exact chlorine, pH, alkalinity and calcium doses.
- Estimate running costs: the Hot Tub Running Cost Calculator uses tub size to estimate monthly electricity and chemical costs.
- Plan water changes: drain and refill every 3–4 months. A common rule of thumb is gallons ÷ 3 ÷ average daily bathers = days between drains.
- Have a pool too? Use the Pool Volume Calculator for your pool’s gallons.
Frequently Asked Questions
How many gallons is a standard hot tub?
A standard 5- to 6-person hard-shell hot tub holds about 350–450 gallons. Small 2–3 person tubs hold 200–300 gallons, and large 7–8 person tubs hold 450–550.
How much does a full hot tub weigh?
Most full hot tubs weigh between 3,000 and 6,000 pounds including water and bathers. Water accounts for most of it: every 100 gallons adds about 834 pounds.
Can my deck hold a hot tub?
Usually not without reinforcement. Standard decks are built for about 50 pounds per square foot, and most full hot tubs put 90–120 pounds per square foot on their footprint. Have a builder or structural engineer check your framing, footings and joist spans before installing a tub on a deck.
How do I find my hot tub’s exact gallons?
Check the owner’s manual or the manufacturer’s spec sheet for your model. You can also read your water meter before and after filling, which gives an exact figure.