Hot tubs hold only a few hundred gallons of hot, heavily used water, so a small dose of the wrong chemical swings the balance fast. Enter your tub’s volume and your latest test-strip or test-kit readings below to see how much of each chemical to add, in ounces and teaspoons.
Hot Tub Chemical Calculator
Enter your test results to see how much chlorine, pH adjuster, alkalinity or calcium to add.
Most hot tubs hold 250 to 600 gallons. Check your owner's manual for the exact number, or measure your tub with our Hot Tub Volume Calculator.
Keep 3–5 ppm day to day. Use 10 ppm to shock after heavy use or if the water is cloudy.
Ideal hot tub pH is 7.4–7.6. Adjust alkalinity first if it's off, since it affects how pH moves.
Ideal range is 80–120 ppm.
Most hot tub makers recommend 150–250 ppm. Check your manual, since some acrylic tubs call for less.
Chlorine
Add
()
Raises free chlorine by ppm.
Chlorine is already at or above target. Nothing to add.
pH
Add
()
Acid demand varies with alkalinity. Add about half, run the jets for 20 minutes, retest, then add the rest if needed.
pH is already at target. No adjustment needed.
Total Alkalinity
Add
()
Alkalinity is already at or above target. If it's too high, lowering pH with acid will slowly bring it down.
Calcium Hardness
Add
()
Calcium is already at or above target. The only way to lower it is a partial drain and refill.
Need to restock?
Shop spa chlorine, pH and alkalinity balancers, and test strips on Amazon.
Shop Hot Tub Chemicals on Amazon →Want to know what your tub costs to run each month? Try our Hot Tub Running Cost Calculator.
Ideal Hot Tub Chemical Levels
These are the ranges most hot tub manufacturers recommend. Your owner’s manual has the final word, especially for calcium hardness.
| Reading | Target Range | Too Low | Too High |
|---|---|---|---|
| Free chlorine | 3–5 ppm | Bacteria and cloudy water | Skin and eye irritation, strong smell |
| Bromine (if you use it) | 3–5 ppm | Bacteria and cloudy water | Skin and eye irritation |
| pH | 7.4–7.6 | Corrosion, itchy skin and eyes | Scale, cloudy water, weaker sanitizer |
| Total alkalinity | 80–120 ppm | pH bounces around | pH keeps drifting up, cloudy water |
| Calcium hardness | 150–250 ppm | Foaming, can etch surfaces | Scale on the shell, jets and heater |
How to Balance Hot Tub Water, Step by Step
- Test the water. Use fresh test strips or a liquid test kit, with the jets off and the water at its normal temperature.
- Fix alkalinity first. Alkalinity acts as a buffer for pH, so getting it into range first keeps the pH adjustment from bouncing. Raise it with baking soda (sodium bicarbonate).
- Adjust pH. Raise it with soda ash (sold as pH Up or pH Increaser). Lower it with dry acid (sodium bisulfate, sold as pH Down) or a small amount of muriatic acid. Add part of the dose, wait, and retest, because acid demand changes with alkalinity.
- Adjust calcium if needed. Raise it with calcium chloride. If calcium is too high, the only real fix is draining part of the water and refilling.
- Bring sanitizer up to range. Add chlorine last, once the water is balanced, so it works at full strength.
Add each chemical separately, with the cover open and the jets running, and wait 20 to 30 minutes before testing and adding the next one. Never mix chemicals together, especially chlorine and acid.
Dichlor vs. Bleach vs. Bromine
Dichlor granules are the most common hot tub chlorine. They dissolve quickly, are close to pH-neutral, and contain stabilizer that helps chlorine last in outdoor tubs. The trade-off is that stabilizer slowly builds up, which is one reason hot tubs need a fresh fill every few months.
Plain unscented household bleach works as hot tub chlorine and adds no stabilizer. Use only plain, unscented bleach with no added fragrance, thickener or “splash-less” formula, and check the label for its strength. The calculator assumes 6%, so if yours is a different strength, adjust the amount to match.
Bromine is usually added through tablets in a floating dispenser rather than dosed by the ounce, so this calculator doesn’t dose it directly. Many owners like bromine because it holds up well in hot water and has less of a chemical smell. Keep bromine at 3 to 5 ppm, and don’t switch between chlorine and bromine without draining and refilling first.
When to Shock a Hot Tub
Shocking raises sanitizer well above normal for a short time to burn off body oils, lotions and other waste that build up with use. A common routine is once a week, plus after a party or any time the water looks dull, smells strongly of chlorine or feels slick. To shock with chlorine, set the calculator’s target to 10 ppm, leave the cover open for at least 20 minutes afterward, and wait until chlorine drops back to 5 ppm or below before soaking.
How Often to Test and Drain
- Test sanitizer and pH two or three times a week, and before soaking if the tub hasn’t been used in a while.
- Test alkalinity and calcium about once a week.
- Drain and refill every three to four months for most households, or sooner with heavy use. Fresh water resets stabilizer, dissolved solids and calcium buildup that chemicals can’t fix.
- Rinse the filter every week or two and deep-clean or replace it on the schedule in your manual.
Curious what all those chemicals and the electricity add up to each month? Our Hot Tub Running Cost Calculator estimates both.
Frequently Asked Questions
How much chlorine do I put in a hot tub?
It depends on the tub’s volume and how far your reading is from target. For a typical 400-gallon tub, raising free chlorine by 3 ppm takes about 0.3 oz of dichlor granules (a bit under 2 teaspoons) or about 2.5 fl oz of 6% bleach. Enter your own numbers above for an exact dose.
Can I use baking soda in my hot tub?
Yes. Plain baking soda is sodium bicarbonate, the same active ingredient in most “alkalinity increaser” products. It raises alkalinity and nudges pH up slightly.
Can I use muriatic acid in a hot tub?
You can, but the doses are small and the acid is strong, so measure carefully, dilute it in a bucket of tub water first (always add acid to water, never water to acid), pour it slowly near a running jet, and wear gloves and eye protection. Many owners find dry acid easier and safer to handle in spa-sized amounts.
Why does my hot tub pH keep going up?
Hot water, running jets and air bubbles drive off carbon dioxide, which pushes pH up over time. High alkalinity makes it worse. Bring alkalinity toward the low end of the range, then lower pH with acid. It usually takes a few rounds over several days.
Are the teaspoon amounts exact?
No. Granular chemicals vary in how densely they pack, so teaspoon amounts are approximate. For the most accurate dose, use a small kitchen scale and the ounce figure, and always check your product’s label.